Skip to main content
For enquiring about prices, please contact us.

Membrane Press Adhesive Manufacturer in India

Spray Grade Adhesive for PVC Foil on MDF Doors and Shutters

Membrane doors and 3D shutters only look premium if the foil stays down. If the bond is weak, PVC lifts at routed grooves, bubbles show up near the heat of a kitchen hob, and edges peel within months.

Synergy Bonding manufactures water-based membrane press adhesives built for Indian door and furniture plants that run vacuum and membrane press lines every day. As an established adhesive manufacturer in Pune with over 19 years of experience, in-house R&D and two production plants, we supply consistent batches in bulk to manufacturers across India.

What Is a Membrane Press Adhesive?

A membrane press adhesive bonds thin decorative PVC foil onto routed MDF or particle board in three dimensions. Most membrane adhesives are based on a water-borne polyurethane adhesive dispersion, applied with a spray gun in the same way as a spray adhesive, then dried before pressing.

Because the adhesive is dried before pressing, boards can be sprayed in batches and pressed later, which suits high-volume production.

How the Membrane Press Process Works

The process works in four stages:

StageWhat happensTypical range
SprayingAdhesive is sprayed evenly over the face, edges and router grooves100 to 150 g/m² wet
DryingWater evaporates until the film turns clear and tack-free30 to 60 minutes at room temperature
PressingHeated membrane pulls the PVC foil over the board under vacuum60 to 180 seconds
ActivationHeat reactivates the dried adhesive film so it bonds to the foilBond line around 55 to 70°C

Our Membrane Press Adhesive Range

OMBOND® Membrane Adhesive

Our core spray grade for membrane doors and shutters. OMBOND® Membrane Adhesive gives an even spray pattern, dries quickly, and activates cleanly in the press for a firm grip on deep routing and profiled edges.

Two-Component Grade (with Hardener)

Mixed with a cross-linker before use. Gives higher heat and water resistance and is the right choice for kitchen shutters, bathroom vanities and export-grade doors.

High Heat-Resistance Grade

Made for parts that sit near ovens, hobs and warm spaces. Keeps the foil from creeping or bubbling at the edges where heat builds up.

Low-Activation Grade

Activates at lower press temperatures. Useful for thin or high-gloss foils that can distort or lose shine when heated too much.

Related Products

For flat PVC sheet pasting without a press, see OMBOND® PVC Adhesive. For curved laminate edges on countertops and tabletops, our post forming adhesive range is the better fit.

OMBOND® Membrane Adhesive

OMBOND® Membrane Adhesive

Single component, low heat activation sprayable adhesive for PVC foil to MDF in membrane and vacuum press machines.

OMBOND® PVC Adhesive

OMBOND® PVC Adhesive

For flat PVC sheet pasting on wood, MDF and plywood without a press.

OMBOND® Post Forming Adhesive

OMBOND® Post Forming Adhesive

For laminates heated and bent around curved countertop and tabletop edges.

Key Features

  • Strong grip on deep router patterns, sharp profiles and edges
  • Fine, even spray with very little overspray or clogging
  • High green strength so the foil holds at once after pressing
  • Good resistance to heat, moisture and humidity after curing
  • Water-based, with low odour and no harsh solvents on the shop floor
  • Colour-tinted film to make it easy to check spray coverage
  • Stable batch-to-batch quality for repeatable press results

Applications

  • Membrane doors and flush doors with 3D designs
  • Modular kitchen shutters and cabinet fronts
  • Wardrobe shutters and sliding panels
  • Bathroom vanity doors
  • TV units, display panels and decorative wall panels
  • Speaker boxes and moulded furniture components
  • Office furniture fronts and storage units

Membrane pressing is one of several ways to finish MDF with PVC. Manufacturers who also bond PVC panels and sheets onto plywood can pair this range with our PVC to wood adhesive.

Industries We Serve

IndustryTypical use
Door manufacturingMembrane and moulded doors for homes and projects
Modular kitchensShutters with high heat and water exposure
Furniture OEMsWardrobes, storage and office furniture, alongside our wider furniture adhesive range
Interior fit-out firmsCustom panels for residential and commercial projects
Panel processorsJob-work pressing of MDF components, often next to lamination adhesive lines

Why Choose Synergy Bonding

ReasonWhat it means for you
19+ years in adhesivesFormulation experience across wood, PVC, lamination and industrial bonding
In-house R&DWe test grades against real foils, boards and press settings before supply
Two manufacturing plantsSteady capacity for repeat bulk orders
Technical supportHelp with spray setup, drying time and press temperature when you start using our adhesive or change foils
Documented specsTechnical and safety datasheets for your quality team on our downloads page
Pan-India supplyRegular dispatches to manufacturers in every major market

Bulk Supply and Custom Formulations

  • Each membrane press line runs differently. Press temperature, foil thickness, gloss level and the factory’s climate all affect the bond.
  • We can adjust viscosity, activation temperature, solids content and heat resistance to suit your line.
  • Bulk orders ship in drums and carboys, with packing sizes agreed to match your monthly use.

Private Label and Multi-Grade Sourcing

Our private labelling is available for distributors and brands that want membrane adhesive under their own name.

Buyers sourcing several grades at once can explore our full industrial adhesive portfolio.

FAQs

Which adhesive is used for membrane doors?

Membrane doors use a water-based polyurethane dispersion adhesive. It is sprayed onto the MDF, dried, and then heat-activated in a vacuum or membrane press to bond the PVC foil.

Why does PVC foil peel from membrane doors?

Common causes are too little adhesive in the grooves, a film that has not dried fully, low press temperature, or an adhesive with poor heat resistance. A two-component grade and correct press settings fix most cases.

How long should the adhesive dry before pressing?

Usually 30 to 60 minutes at room temperature, until the film is clear and dry to the touch. Drying takes longer in humid weather.

Is a hardener necessary for membrane press adhesive?

Not for general furniture. For kitchen and bathroom shutters or parts near heat, adding a hardener improves heat and water resistance a lot.

Can the same adhesive be used for high-gloss foils?

Yes, but a low-activation grade is better because it lets you press at lower temperatures and keeps the gloss intact.

Do you supply membrane press adhesive in bulk across India?

Yes. We supply drums and carboys to door and furniture manufacturers across India, and custom grades are available for larger volumes.

Contact

Synergy Bonding Solutions

Adhesive manufacturer, India — samples, pricing & partnerships

Choose the path that fits you: a tracked business enquiry for distributor, export, bulk, or private-label work — or a fast WhatsApp message for urgent questions.

Business enquiry

For distributor, export, bulk orders, or private label — submit here so our team can track and follow up in CRM.

Quick message on WhatsApp

Same details below are formatted and sent to our sales WhatsApp.

Your details
Product & quantity
Message